Showing results: 1591 - 1605 of 1638 items found.
-
LA-1 HC -
Walter G. Legge Company Inc.
LA-1 HC Floor Conductivity Tester Hand Crank is an easy-to-use meter developed for accurately testing the conductivity of floors and equipment. The LA- 1 must be used regularly to monitor proper conductivity with NFPA code # 99. Regular use of the LA-1 will establish and maintain procedures for the proper maintenance of conductive floors, eliminate fire hazards, and provide a static free environment. A hand crank AC type generator provides a rectified DC test potential. Additionally, there are no brushes to wear out. The LA-1 has an easy-to-read scale that is selectively expanded electronically to assure accurate readings over the entire range of the instrument and the scale has a length of 3.75. This is 42% longer than typical competitive testers. The LA-1 uses 500V DC to test the resistance (in ohms) between two points. (NFPA Code #99) The meter comes ready-to-use (tin foil must be applied to bottom of weights). Simply follow the instructions for use and instantly obtain an accurate measurement. Choose electric or hand powered model.
-
Ponovo Power Co., Ltd.
With the development of power system, more and more digital substation based on IEC61850 has been built in the world. IEC61850 is the new communication protocol which is adopted by power system so as to change the analog complicated wiring connection and protocol conversion. Based on IEC61850, all Messages, such as GOOSE, SV, MMS, PTP, etc, could be communicated on the Ethernet via fiber optical cable connection. In China, the digital substation have started since 2003, until now there are already more than 6000 digital substation put on operation, China Power Grid is planning to build 5000 more new digital substations. PONOVO, as the leading power system testing solution provider, have launched plenty of IEC61850 digital testing tools, not only digital relay test set, but also MU test set, multi-functional analyzer, 24 hours online monitoring and analyzing system, etc so that users could have suitable testing equipment for the digital substation commissioning and testings.
-
Model 3580 -
Jinan Testing Equipment IE Corporation
This model is for diametral strain measurement with furnace and induction heating systems. Quartz rods and water-cooling allow the unit to be used for high temperature testing of metals, ceramics and composites. With induction heating, this model often can be used without water-cooling. When used in furnaces, the extensometer is often mounted directly to the furnace side cut-out. Optional load frame mounting brackets are available for supporting the extensometer in cases where furnace mounting is not possible. These optional mounts are used with induction heating or furnace systems. The Model 3580 extensometers are strain gaged devices, making them compatible with any electronics designed for strain gaged transducers. Most often they are connected to a test machine controller. The signal conditioning electronics for the extensometer is typically included with the test machine controller or may often be added. In this case the extensometer is shipped with the proper connector and wiring to plug directly into the electronics. For systems lacking the required electronics, Epsilon can provide a variety of solutions, allowing the extensometer output to be connected to data acquisition boards, chart recorders or other equipment.
-
Model 4013 -
Jinan Testing Equipment IE Corporation
The Model 4013 extensometer meets the requirements of ASTM D5656 for measuring the strain properties of an adhesive in shear. It uses different contact point spacing compared to the extensometer shown in D5656. This makes it much easier to mount and eliminates the slippage problems associated with the design shown in the ASTM standard. The Model 4013 is available with all of Epsilon’s temperature configurations. It has a 3.0 mm (0.12 inches) full scale measuring range. The conical point contacts included with the extensometer are made from tungsten carbide.The Model 4013 extensometers are strain gaged devices, making them compatible with any electronics designed for strain gaged transducers. Most often they are connected to a test machine controller. The signal conditioning electronics for the extensometer is typically included with the test machine controller or may often be added. In this case the extensometer is shipped with the proper connector and wiring to plug directly into the electronics. For systems lacking the required electronics, Epsilon can provide a variety of solutions, allowing the extensometer output to be connected to data acquisition boards, chart recorders or other equipment.
-
MB Dynamics Inc.
Electrodynamic shaker systems and amplifiers from MB Dynamics help to support a wide range of general-purpose vibration test requirements. The electrodynamic shaker systems are offered in a variety of force ranges, from 100N (25 lbf) to 22kN (5,000 lbf). The innovative design of MB Dynamics PM-Series electrodynamic shakers incorporates permanent magnet technology and the voice coil principle to create vibration. These heavy-duty electrodynamic shakers feature a robust design for maximum reliability, with end-users reporting a useful service life of 10, 25 or even 40 years! The shakers come in five unique sizes, with peak sine force ratings of 100 N, 200 N, 500 N, 1000 N and 2000 N; or, 25 lbf, 50 lbf, 100 lbf, 250 lbf and 500 lbf. The MB Dynamics C40HP electrodynamic shaker outputs 22 kN or 5,000 lbf peak. The C40HP is a part of the legacy C-Series of shakers, which have served as the foundation for today’s modern electrodynamic vibration test equipment industry.
-
66309D -
Keysight Technologies
The Keysight Mobile Communications DC Source 663xx series offers several features ideal for testing wireless and battery powered devices. Excellent voltage transient response ensures maximum test-system throughput by minimizing device shutdowns due to significant voltage drops in the test wiring. Built-in advanced measurement system to accurately measure battery current drains when the device operates in different modes and a Keysight-developed feature that enables cellular telephone manufacturers to detect permanently and intermittently open-sense wire connections.The Keysight 66309D dual output mobile communications dc source provides two outputs for testing both the main battery power and the battery charger circuitry, allowing customers to test phones and chargers with the same equipment. This feature helps save on rack space (2 outputs in a half rack box) and eliminates the need for two separate power supplies.The 66309D dc source provides all of the capabilities of the 66309B with the addition of a built in digital voltmeter.
-
Model 3911 -
Jinan Testing Equipment IE Corporation
For indirect tensile testing, such as for resilient modulus, these extensometers measure the lateral deformation of specimens. They are self-supporting on the sample and clip on in seconds. The traditional way this deformation has been measured was prone to errors caused by slight rocking of the sample as it is loaded. The self-supporting design of the Model 3911 eliminates this problem. This unit will handle the dynamic pulse requirements of resilient modulus testing.The speed of mounting makes test set-up much faster than with the older method. The pivot mounting used ensures that the specimen contact pads meet the often uneven asphalt surface as well as possible. The measuring range options available allow a wide range of testing, yet can easily measure the sometimes very small displacements required.The Model 3911 extensometers are strain gaged devices, making them compatible with any electronics designed for strain gaged transducers. Most often they are connected to a test machine controller. The signal conditioning electronics for the extensometer is typically included with the test machine controller or may often be added. In this case the extensometer is shipped with the proper connector and wiring to plug directly into the electronics. For systems lacking the required electronics, Epsilon can provide a variety of solutions, allowing the extensometer output to be connected to data acquisition boards, chart recorders or other equipment.
-
OMK-SR-OTS.2 -
OPTOKON a.s.
Diagnostic set includes measuring instruments and tools for diagnosing faults on fiber optic cables with connectors STRATOS and CTOS, and direct technical successors connectors HMA. The OPTOKON Diagnostic Set includes two instruments - Light source and Power meter. Both instruments are housed in a hard carry case that meets the requirement of fiber optic networks installation and maintenance teams, who require rugged and lightweight fiber optic test equipment that combines high performance with ease of use and reliable operation. The Diagnostic Set allows traceable measurements on dual wavelength and data storage to the PC. It includes the hybrid master HMA-FC patchcord for testing of harsh environmental networks and is comprised of these measurement instruments: LS-800 light source and PM-800 power meter
-
PrimeTest Automation
Our team of experienced mechanical, electrical, and software engineers fabricate all types of assembly systems, ranging from complicated multi-step assemblies to simple single step assemblies. We have a full machine shop to manufacture systems from materials such as plastic, aluminum, steel, and stainless steel. All our systems are expandable and allow for future enhancements with modular components. They are available with a variety of options, including human machine interfaces, welding, marking, packaging, and test equipment. Additional features include emergency stop safety circuitry and hard guarding. All fabricated systems are provided with the necessary pneumatic and electrical system layouts in addition to the associated documentation. Our services also include onsite setup, training, and support operations.
-
National Technical Systems
Lightweight Shock Machine (LWSM) Testing per MIL-DTL-901E is the military specification covering shock test requirements for shipboard machinery, equipment, systems and structures. Anyone who produces an item for military use in any of these shipboard categories will likely need to complete this testing. The purpose of this testing is to verify the ability of shipboard installations to withstand shock loadings which may be incurred during wartime service due to the effects of conventional or nuclear weapons. These requirements grew out of the Navy’s experiences during World War II and the subsequent underwater explosion (UNDEX) experiments. In many cases, it was found that critical ship systems could be disabled by the shock effects of nearby weapons explosions that were not a direct hit on the ship itself.
-
JB-(C/D) -
Jinan Testing Equipment IE Corporation
KB- (C/D) common type metallic pendulum impact testing system is the basic model for impact tester. The metallic pendulum impact tester is used to determine the impact resistance of metal materials under dynamic load and capable of doing a large number of impact tests continuously. The display method for the models is different, respectively there are analog dial display, touch screen digital display and computer display. For the later two models, it can display the impact power, impact toughness, and pendulum rotation angle. All the testing reports can be printed out. The metallic pendulum impact testing system is the essential quality control equipment for metal material manufacturers and QC departments, as well as the necessary instrument of research institutes for new material research.
-
CZ20152 -
Aegis Pty. Ltd.
The CZ20153 is the latest design technology providing voice, data, and video technicians/engineers all the functionality essential in a test set. This model builds on the CZ20123 by adding features specifically useful for modern digital communications including Data Indication, Voltage/Current measurement, Caller ID with Call Waiting, and DTMF Digit Grabbing. All of these extra features are essential for working on modern phone systems. With these additional features you can determine whether data is on the line, whether the voltage is sufficient, whether the line current is sufficient, verify the Caller ID & Call Waiting, and isolate faulty customer premise equipment(CPE). Also included are the RainSafeTM, DropSafeTM, and DataSafeTM technologies making it truly rugged and robust backed up by a 3 year warranty.
-
RF Explorer -
Nuts About Nets, llc
RF Explorer is a new series of low-cost, portable, RF spectrum analyzers designed by Arocholl that are available in a variety of frequency ranges. Nuts About Nets has been developing diagnostic tools for troubleshooting wireless networks for a number of years and when RF Explorer was first introduced to us we were extremely impressed. The price-performance of these RF spectrum analyzers is truly remarkable and is the best, by far, on the market -- nothing else comes close. These RF analyzers operate both standalone as handheld devices, plus they interface via USB cable to a PC running more sophisticated data acquisition and analysis software. Prices for these RF spectrum analyzers (including PC software) begin at $119 USD -- which is unheard of in the test equipment industry.
-
17040 -
Chroma ATE Inc.
Conforms to international standards for battery testing: IEC, ISO, UL, and GB/T, etc.Regenerative battery energy discharge (Eff. >90%, PF >0.95, I_THD <5%)Multiple voltage and current ranges for auto ranging function to provide optimum resolutionHigh accuracy current/voltage measurement (0.05%FS/0.02%FS)2ms current slew rate (-90% ~ 90%)Dynamic (current/power) driving profile simulation tests for NEDC, FUDS, HPPCTest channel parallel functionTest data analysis functionData recovery protection (after power failure)Automatic protection for error conditionBattery simulator (option)High power testing equipment- Voltage range : 80~1000V - Current range : 0~750A - Power range : 0~300kWCustomized integration functions- Integrated temperature chamber - BMS data analysis - Multi-channel voltage/temperature recording
-
PE-100 -
Pansco, Ltd
The PoE Tester/Power Monitor is designed for testing standard PoE and measuring power of PoE systems, by performing both PSE (Power Source Equipment) detecting and PSE/PD (Powered device) inline testing. Compliant with IEEE802.3 af, 802.3at standard and 802.3bt ultra 4-pair up to 60W-100W. PSE detecting display PoE type (af or at), power source (Endspan or Midspan) and perform a load test for voltage drop with REV LED indicates a reversed power. Inline PSE/PD testing-measure and display in rotation between voltage (Volts), current(Amps) and power(Watts) via dual 4 digit 7 segment LEDs which provides voltage available, current flowing and how much power an PD actually need ensure sufficient power for PD to make the PoE is sustainable.
